MIDWEST MIXING, INC
5630 Pleasant Avenue
Chicago Ridge, IL 60415
Ph: 708-422-8100
800-879-8971
Fax: 708-422-8140
Website by:
Advantage Internet
|
|
Electric
|
Operate from 60 cycle AC Source
Direct drive or Geared drip proof, totally enclosed, or explosion proof
Miniaruized, Solid State, Electronic Control
Wide Speed Range
Full Rated Torque at All Speeds
These portable mixers have the same proven components as our constant speed mixers.
- A firm mounting assembly with rapid acting universal ball and socket swivel clamp,
adjustable through 360 degrees in a horizontal plane, tilts back 100 degrees to clear
tank. Broad clamp face to grip tank edge. Accurate sleeve coupling. Precision shafting.
Balanced, high performance propellers. Geared models offer heavy duty gears and wide bearing
span for shaft support.
MOTORS
Shunt wound continuous duty, DC motors are used. Totally enclosed and explosion
proof motorshave a 75 degree C rise above ambient at full load, and Class B Insulation. 120
volts in fractional sizes, and 120 or 240 volts integral.
CONTROLS
For the ultimate in speed control, a shunt wound motor with a full wave transistorized
silicon rectifier is used. These provide full range speed from 0 to 1725 RPM, or 0 to 430 RPM in the
geared models, with full rated torque over the whole range. Where constant pre-set speed under varying
load is desired, this combination is suggested. Protected against overload.
Full wave controls with various features, for operation from 230 volt, 60 cy., 3 phase current supply,
require separate rectifier assembly in wall mounted cabinet. Attached or remote operator station, any
enclosure. Higher voltages reduceable by transformer.
Variable speed drives are available for vertical flange mounted or side entering mixers to 75 horse
power.
|
GEARED MIXERS 0-400 RPM
FOR VISCOUS MATERIALS AND SLURRIES
DIMENSIONS*
| Model |
HP |
A |
B |
C |
D |
E Dual |
Wt. |
| 31V |
1/4 |
22 3/4" |
17 3/4" |
30" |
3/4" |
8 |
65 |
| 32V |
1/3 |
23 1/4" |
18 1/4" |
36" |
3/4" |
9 |
67 |
| 33V |
1/2 |
23 3/4" |
18 3/4" |
36" |
3/4" |
10 |
74 |
| 34V |
3/4 |
24 1/2" |
19 1/2" |
36" |
7/8" |
11 |
83 |
| 35V |
1 |
30 1/4" |
25 1/2" |
42" |
7/8" |
12 |
138 |
| 36V |
1 1/2 |
32 5/8" |
27 5/8" |
48" |
1" |
13 |
169 |
| 37V |
2 |
33 1/8" |
28 1/8" |
54" |
1 1/8" |
14 |
175 |
| 38V |
3 |
33 1/2" |
28 1/2" |
54" |
1 1/4" |
15 |
234 |
* Approx - Refer to Factory for certified prints.
DIRECT DRIVE MIXERS 0-1800 RPM
FOR THIN LIQUIDS
DIMENSIONS*
| Model |
HP |
A |
B |
C |
D |
E Dual |
Wt. |
| 55 |
1/6 |
9" |
7 1/2" |
18" |
3/8" |
3(1) |
6 |
| 11V |
1/4 |
10 3/4" |
12 1/2" |
30" |
5/8" |
3 |
48 |
| 12V |
1/3 |
11 1/2" |
14" |
36" |
5/8" |
4 |
48 |
| 13V |
1/2 |
11 1/2" |
14" |
36" |
5/8" |
4 1/2 |
54 |
| 14V |
3/4 |
12 1/2" |
15" |
36" |
3/4" |
4 1/2 |
61 |
| 15V |
1 |
18 3/8" |
21 1/4" |
42" |
7/8" |
5 |
148 |
| 16V |
1 1/2 |
20 11/16" |
23 3/4" |
48" |
7/8" |
5 |
155 |
| 17V |
2 |
21 5/16" |
24 3/8" |
54" |
1" |
6 |
159 |
| 18V |
3 |
22 5/16" |
25 1/2" |
54" |
1" |
6 |
207 |
* Approx - Refer to Factory for certified prints.
| Model 55C
Laboratory mixer, heavy duty, 1/4 HP, totally enclosed, 115/1/60, 0-3600 RPM.
Solid state SCR speed control, constant torque. For heavier than normal lab jobs.
Clamp mounted: 3/8 x 18 stainless shaft, two inch dia. three blade propeller.
Model 55R
Lab mixer, as above but with rign stand mounting.
Model 56G
Lab Mixer, TEFC, 0-180 RPM, 8 in-lbs. torque, SCR full torque speed control,
12" stainless shaft, 6" dia. four-blade paddle. For mixing viscous fluids.
Model 56GC
Lab mixer, as above but clamp mounted.
|
|
info@midwestmixing.com
|
